Skip to content

8‐3 Delete Commands_jp

Jump to bottom
Yusuke Ogawa edited this page Sep 11, 2025 · 9 revisions

Masterファイルを直接編集するため、実行前に必ずMasterファイルをバックアップしてください。

本手順でできること

CLIから以下のdeleteコマンドを実行できます

基本構文

python [file path]/network_sketcher.py [command] --master [master file path]
  • 以下のように[command] 、--master [master file path]　の場所は変更可能
    python [file path]/network_sketcher.py -master [master file path] [command]

delete ip_address

レイヤ３インタフェースのIPアドレスを削除します。１回に１つのIPアドレスが削除できます。

python [file path]/network_sketcher.py delete ip_address [hostname] [layer3_portname] [ip_address/subnetmask] --master [master file path]
  • ex.

+BEFORE+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 100', '', '192.168.100.100/24']

+IP Address deleted+
＃python .\network_sketcher.py delete ip_address 'L3SW2' 'Vlan 100' '192.168.100.100/24' --master "C:\work\[MASTER]test.xlsx"
--- IP Address deleted --- L3SW2,Vlan 100,192.168.100.100/24

+AFTER+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 100', '', '']

delete l2_segment

インタフェースに設定されたVLAN等のレイヤ２セグメントを削除します。１回に１つのレイヤ２セグメントが削除できます。

python [file path]/network_sketcher.py delete ip_address [hostname] [layer2_portname] [l2segment_name] --master [master file path]
  • ex.

+BEFORE+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'GigabitEthernet 0/0', '', 'Vlan100,Vlan200,Vlan300,addvlan999', '']

+l2_segment deleteed+
＃python .\network_sketcher.py delete l2_segment 'L3SW2' 'GigabitEthernet 0/0' 'addvlan999' --master "C:\work\[MASTER]test.xlsx"
--- l2 Segment deleted --- L3SW2,GigabitEthernet 0/0,addvlan999

+AFTER+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'GigabitEthernet 0/0', '', 'Vlan100,Vlan200,Vlan300', '']

delete virtual_port

VLANインタフェース(SVI)等のレイヤ３インタフェースを削除します。

python [file path]/network_sketcher.py delete virtual_port [hostname] [virtual_portname] --master [master file path]
  • ex.

+BEFORE+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', '', 'addvlan 999', '', '']
['L3SW2', '', 'Vlan 300', 'Vlan300', '']

#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 300', '', '']
['L3SW2', 'addvlan 999', '', '']

+virtual_port added+
＃python .\network_sketcher.py delete l2_segment 'L3SW2' 'GigabitEthernet 0/0' 'addvlan999' --master "C:\work\[MASTER]test.xlsx"
--- Virtual Port deleted --- L3SW2,addvlan 999

+AFTER+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', '', 'Vlan 300', 'Vlan300', '']

#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 300', '', '']

Author

  • Yusuke Ogawa - Security Architect, Cisco | CCIE#17583

License

SPDX-License-Identifier: Apache-2.0

Copyright 2023 Cisco Systems, Inc. and its affiliates

Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

Clone this wiki locally