Merge pull request #120 from tasmota/s3_tasmota_work

S3 tasmota work

Author: Jason2866

boards.txt

@@ -37,7 +37,7 @@ void serialEvent(void) {}
 #ifndef RX1
 #if CONFIG_IDF_TARGET_ESP32
 #define RX1 9
-#elif CONFIG_IDF_TARGET_ESP32S2 
+#elif CONFIG_IDF_TARGET_ESP32S2
 #define RX1 18
 #elif CONFIG_IDF_TARGET_ESP32C3
 #define RX1 18
@@ -86,8 +86,6 @@ void serialEvent2(void) {}
 #if !defined(NO_GLOBAL_INSTANCES) && !defined(NO_GLOBAL_SERIAL)
 #if ARDUINO_USB_CDC_ON_BOOT //Serial used for USB CDC
 HardwareSerial Serial0(0);
-#elif ARDUINO_HW_CDC_ON_BOOT
-HardwareSerial Serial0(0);
 #else
 HardwareSerial Serial(0);
 #endif
@@ -102,8 +100,6 @@ void serialEventRun(void)
 {
 #if ARDUINO_USB_CDC_ON_BOOT //Serial used for USB CDC
     if(Serial0.available()) serialEvent();
-#elif ARDUINO_HW_CDC_ON_BOOT
-    if(Serial0.available()) serialEvent();
 #else
     if(Serial.available()) serialEvent();
 #endif
@@ -127,7 +123,8 @@ void serialEventRun(void)
 HardwareSerial::HardwareSerial(int uart_nr) : 
 _uart_nr(uart_nr), 
 _uart(NULL), 
-_rxBufferSize(256), 
+_rxBufferSize(256),
+_txBufferSize(0), 
 _onReceiveCB(NULL), 
 _onReceiveErrorCB(NULL),
 _eventTask(NULL)
@@ -295,7 +292,7 @@ void HardwareSerial::begin(unsigned long baud, uint32_t config, int8_t rxPin, in
     }
 
     // IDF UART driver keeps Pin setting on restarting. Negative Pin number will keep it unmodified.
-    _uart = uartBegin(_uart_nr, baud ? baud : 9600, config, rxPin, txPin, _rxBufferSize, invert, rxfifo_full_thrhd);
+    _uart = uartBegin(_uart_nr, baud ? baud : 9600, config, rxPin, txPin, _rxBufferSize, _txBufferSize, invert, rxfifo_full_thrhd);
     if (!baud) {
         // using baud rate as zero, forces it to try to detect the current baud rate in place
         uartStartDetectBaudrate(_uart);
@@ -309,7 +306,7 @@ void HardwareSerial::begin(unsigned long baud, uint32_t config, int8_t rxPin, in
 
         if(detectedBaudRate) {
             delay(100); // Give some time...
-            _uart = uartBegin(_uart_nr, detectedBaudRate, config, rxPin, txPin, _rxBufferSize, invert, rxfifo_full_thrhd);
+            _uart = uartBegin(_uart_nr, detectedBaudRate, config, rxPin, txPin, _rxBufferSize, _txBufferSize, invert, rxfifo_full_thrhd);
         } else {
             log_e("Could not detect baudrate. Serial data at the port must be present within the timeout for detection to be possible");
             _uart = NULL;
@@ -458,10 +455,26 @@ size_t HardwareSerial::setRxBufferSize(size_t new_size) {
     }
 
     if (new_size <= SOC_UART_FIFO_LEN) {
-        log_e("RX Buffer must be higher than %d.\n", SOC_UART_FIFO_LEN);
+        log_e("RX Buffer must be higher than %d.\n", SOC_UART_FIFO_LEN);  // ESP32, S2, S3 and C3 means higher than 128
         return 0;
     }
 
     _rxBufferSize = new_size;
     return _rxBufferSize;
 }
+
+size_t HardwareSerial::setTxBufferSize(size_t new_size) {
+
+    if (_uart) {
+        log_e("TX Buffer can't be resized when Serial is already running.\n");
+        return 0;
+    }
+
+    if (new_size <= SOC_UART_FIFO_LEN) {
+        log_e("TX Buffer must be higher than %d.\n", SOC_UART_FIFO_LEN);  // ESP32, S2, S3 and C3 means higher than 128
+        return 0;
+    }
+
+    _txBufferSize = new_size;
+    return _txBufferSize;
+}

cores/esp32/HardwareSerial.cpp

@@ -132,11 +132,13 @@ class HardwareSerial: public Stream
     void setHwFlowCtrlMode(uint8_t mode = HW_FLOWCTRL_CTS_RTS, uint8_t threshold = 64);   // 64 is half FIFO Length
 
     size_t setRxBufferSize(size_t new_size);
+    size_t setTxBufferSize(size_t new_size);
 
 protected:
     int _uart_nr;
     uart_t* _uart;
     size_t _rxBufferSize;
+    size_t _txBufferSize;
     OnReceiveCb _onReceiveCB;
     OnReceiveErrorCb _onReceiveErrorCB;
     TaskHandle_t _eventTask;
@@ -156,10 +158,10 @@ extern void serialEventRun(void) __attribute__((weak));
 #define ARDUINO_USB_CDC_ON_BOOT 0
 #endif
 #if ARDUINO_USB_CDC_ON_BOOT //Serial used for USB CDC
+#if !ARDUINO_USB_MODE
 #include "USB.h"
 #include "USBCDC.h"
-extern HardwareSerial Serial0;
-#elif ARDUINO_HW_CDC_ON_BOOT
+#endif
 extern HardwareSerial Serial0;
 #else
 extern HardwareSerial Serial;

cores/esp32/HardwareSerial.h

@@ -117,16 +117,39 @@ size_t USBCDC::setRxBufferSize(size_t rx_queue_len){
     size_t currentQueueSize = rx_queue ? 
             uxQueueSpacesAvailable(rx_queue) + uxQueueMessagesWaiting(rx_queue) : 0;
 
-    if (rx_queue && (!rx_queue_len || rx_queue_len != currentQueueSize)) {
-            vQueueDelete(rx_queue);
-            rx_queue = NULL;
-    }
-    if(!rx_queue_len || rx_queue_len == currentQueueSize){
-        return 0;
-    }
-    rx_queue = xQueueCreate(rx_queue_len, sizeof(uint8_t));
-    if(!rx_queue){
-        return 0;
+    if (rx_queue_len != currentQueueSize) {
+        xQueueHandle new_rx_queue = NULL;
+        if (rx_queue_len) {
+            new_rx_queue = xQueueCreate(rx_queue_len, sizeof(uint8_t));
+            if(!new_rx_queue){
+                log_e("CDC Queue creation failed.");
+                return 0;
+            }
+            if (rx_queue) {
+                size_t copySize = uxQueueMessagesWaiting(rx_queue);
+                if (copySize > 0) {
+                    for(size_t i = 0; i < copySize; i++) {
+                        uint8_t ch = 0;
+                        xQueueReceive(rx_queue, &ch, 0);
+                        if (!xQueueSend(new_rx_queue, &ch, 0)) {
+                            arduino_usb_cdc_event_data_t p;
+                            p.rx_overflow.dropped_bytes = copySize - i;
+                            arduino_usb_event_post(ARDUINO_USB_CDC_EVENTS, ARDUINO_USB_CDC_RX_OVERFLOW_EVENT, &p, sizeof(arduino_usb_cdc_event_data_t), portMAX_DELAY);
+                            log_e("CDC RX Overflow.");
+                            break;
+                        }
+                    }    
+                }
+                vQueueDelete(rx_queue);
+            }
+            rx_queue = new_rx_queue;
+            return rx_queue_len;
+        } else {
+            if (rx_queue) {
+                    vQueueDelete(rx_queue);
+                    rx_queue = NULL;
+            }
+        }
     }
     return rx_queue_len;
 }
@@ -249,26 +272,19 @@ void USBCDC::_onLineCoding(uint32_t _bit_rate, uint8_t _stop_bits, uint8_t _pari
 }
 
 void USBCDC::_onRX(){
+    arduino_usb_cdc_event_data_t p;
     uint8_t buf[CONFIG_TINYUSB_CDC_RX_BUFSIZE+1];
     uint32_t count = tud_cdc_n_read(itf, buf, CONFIG_TINYUSB_CDC_RX_BUFSIZE);
-
-    if(rx_queue == NULL) {
-        return;
-    }
-    if (uxQueueSpacesAvailable(rx_queue) < count) {
-        //this VTaskDelay gives, to Arduino's task, time to the CPU do its processing
-        //without it, data may be lost when the number of bytes received is higher than CDC buffer size
-        vTaskDelay(10);
-    }
     for(uint32_t i=0; i<count; i++){
-        if(!xQueueSend(rx_queue, buf+i, 0)){
-            // rx_queue overflow - data will be lost
+        if(rx_queue == NULL || !xQueueSend(rx_queue, buf+i, 10)) {
+            p.rx_overflow.dropped_bytes = count - i;
+            arduino_usb_event_post(ARDUINO_USB_CDC_EVENTS, ARDUINO_USB_CDC_RX_OVERFLOW_EVENT, &p, sizeof(arduino_usb_cdc_event_data_t), portMAX_DELAY);
+            log_e("CDC RX Overflow.");
             count = i;
             break;
         }
     }
     if (count) {
-        arduino_usb_cdc_event_data_t p;
         p.rx.len = count;
         arduino_usb_event_post(ARDUINO_USB_CDC_EVENTS, ARDUINO_USB_CDC_RX_EVENT, &p, sizeof(arduino_usb_cdc_event_data_t), portMAX_DELAY);
     }

cores/esp32/USBCDC.cpp

@@ -33,6 +33,7 @@ typedef enum {
     ARDUINO_USB_CDC_LINE_CODING_EVENT,
     ARDUINO_USB_CDC_RX_EVENT,
     ARDUINO_USB_CDC_TX_EVENT,
+    ARDUINO_USB_CDC_RX_OVERFLOW_EVENT,
     ARDUINO_USB_CDC_MAX_EVENT,
 } arduino_usb_cdc_event_t;
 
@@ -50,6 +51,9 @@ typedef union {
     struct {
             size_t len;
     } rx;
+    struct {
+            size_t dropped_bytes;
+    } rx_overflow;
 } arduino_usb_cdc_event_data_t;
 
 class USBCDC: public Stream

cores/esp32/USBCDC.h

@@ -130,7 +130,7 @@ void uartSetHwFlowCtrlMode(uart_t *uart, uint8_t mode, uint8_t threshold) {
 }
 
 
-uart_t* uartBegin(uint8_t uart_nr, uint32_t baudrate, uint32_t config, int8_t rxPin, int8_t txPin, uint16_t queueLen, bool inverted, uint8_t rxfifo_full_thrhd)
+uart_t* uartBegin(uint8_t uart_nr, uint32_t baudrate, uint32_t config, int8_t rxPin, int8_t txPin, uint16_t rx_buffer_size, uint16_t tx_buffer_size, bool inverted, uint8_t rxfifo_full_thrhd)
 {
     if(uart_nr >= SOC_UART_NUM) {
         return NULL;
@@ -163,7 +163,7 @@ uart_t* uartBegin(uint8_t uart_nr, uint32_t baudrate, uint32_t config, int8_t rx
     uart_config.source_clk = UART_SCLK_APB;
 
 
-    ESP_ERROR_CHECK(uart_driver_install(uart_nr, 2*queueLen, 0, 20, &(uart->uart_event_queue), 0));
+    ESP_ERROR_CHECK(uart_driver_install(uart_nr, rx_buffer_size, tx_buffer_size, 20, &(uart->uart_event_queue), 0));
     ESP_ERROR_CHECK(uart_param_config(uart_nr, &uart_config));
     ESP_ERROR_CHECK(uart_set_pin(uart_nr, txPin, rxPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE));
 

cores/esp32/esp32-hal-uart.c

@@ -61,7 +61,7 @@ extern "C" {
 struct uart_struct_t;
 typedef struct uart_struct_t uart_t;
 
-uart_t* uartBegin(uint8_t uart_nr, uint32_t baudrate, uint32_t config, int8_t rxPin, int8_t txPin, uint16_t queueLen, bool inverted, uint8_t rxfifo_full_thrhd);
+uart_t* uartBegin(uint8_t uart_nr, uint32_t baudrate, uint32_t config, int8_t rxPin, int8_t txPin, uint16_t rx_buffer_size, uint16_t tx_buffer_size, bool inverted, uint8_t rxfifo_full_thrhd);
 void uartEnd(uart_t* uart);
 
 // This is used to retrieve the Event Queue pointer from a UART IDF Driver in order to allow user to deal with its events